Auto Mechanics Practice Test – All Questions

Browse all practice questions for the Auto Mechanics Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Start practice test Flash cards

A battery charger is the right tool for slow 12-volt battery charging.Which part is primarily responsible for charging a 12-volt battery at a slow rate?A battery load test should apply a load equal to half the CCA rating for 15 to 30 seconds.A battery load test is being performed. The proper method is to:A fully charged 12-volt car battery should read about 12.6 volts on open circuit.A fully charged 12-volt automotive battery should have an open-circuit voltage of:A loose gas cap is a common culprit when the check engine light comes on.What is a common cause of a check engine light being illuminated?A memory saver keeps your radio presets and other electronic settings intact when you disconnect your car battery.What is the main purpose of a memory saver when disconnecting a vehicle's battery?AdBlue is the name you’ll hear most often for diesel exhaust fluid (DEF)Which name is commonly used when discussing diesel exhaust fluid (DEF)?All of the above safety gear is essential when using power tools in an auto shop.Which safety equipment is essential to use when working with power tools in an auto shop?Always gather as much information before starting work on any vehicle.Before starting work on any vehicle, it's important to:ASE Certification Certifies Automotive Professionals and Elevates Service QualityASE tests and certifies which of the following?ASE certification explains who certifies automotive technicians and why it matters.What organization is responsible for certifying automotive technicians?Auto service franchises explained: how Carquest, NAPA, and Jiffy Lube fit the modelCarquest, NAPA, and Jiffy Lube are examples of what type of businesses?B Brakes is the official ASE certification for brake specialists.Which of the following is an official ASE certification?Baking soda and water clean car battery terminals and neutralize acid corrosionWhich solution is effective for cleaning and neutralizing acid corrosion from battery terminals?Ball peen hammers are the most common tool in auto shops, and here's why.What is the most common type of hammer used in an automotive shop?Be careful when releasing a compressed coil spring—use a jack stand to prevent bodily injury.What is the danger of releasing a compressed coil spring without a jack stand in place?Blue smoke at startup usually means worn valve stem sealsIf blue smoke is seen at the tailpipe when an engine is started, which part(s) is/are most likely worn out?Brake fluid is the essential medium that powers hydraulic brakes.Which component is essential for the proper operation of hydraulic brakes?Brake fluid powers clutch master cylinders for smooth shifts.What type of fluid is commonly used in clutch master cylinders?Brake fluid should never be used in a manual transmission.Which fluid should never be installed in a manual transmission?Brake inspection is a fundamental safety check every driver should know.Which of the following is a common automotive maintenance task?Brake lights staying on is usually caused by a stuck brake light switchWhat is the likely cause of brake lights remaining on continuously?Brake pad squeal is a warning sign that your brakes may need replacement.What is a common sign that a vehicle’s brake pads may need replacement?Brake shoes press outward on the drum to stop a vehicle in a drum brake systemWhich part in the drum brake system expands outward against the drum to stop a vehicle when brakes are applied?Can DOT 3 Brake Fluid Be Mixed with DOT 4? Here's What You Need to KnowDOT 3 brake fluid can be safely mixed with which type of brake fluid?Carbon monoxide in car exhaust is dangerous, and proper ventilation protects you.What poisonous gas comes from the exhaust of a vehicle?Check brake light operation safely with a helper and the right steps.What might a technician need to check the operation of brake lights on the rear of a vehicle?Choose the safest way to lift heavy objects by using hoists and other tools for mechanical advantage.Which is the best practice for lifting heavy objects safely?Choosing the right fluids for manual transmissions matters, and sometimes more than one option fits.Who is correct regarding the types of fluid used in manual transmissions?Clutch disc replacement safety shows why asbestos exposure matters and how you can protect yourself.Which is a concern when one is changing a clutch disc?Coolant keeps your engine cool by absorbing heat and sending it to the radiator.What type of fluid is most commonly associated with providing cooling to the engine?Cutting into the orange high-voltage harness on hybrids is dangerous.What is the danger of cutting into an orange covered harness on a hybrid vehicle?Dark brown motor oil with a burnt smell means the oil has degraded and needs changingWhat type of fluid typically leaks if oil is dark brown and has a burnt smell?Diesel exhaust fluid is blue, and that color helps keep engines clean.What color is associated with diesel exhaust fluid?Disarming the airbag: the essential safety step before servicing the supplemental restraint systemBefore servicing the supplemental restraint system, what should a technician do as a safety precaution?Disconnect the negative battery lead first when removing a starter for safer automotive electrical work.Before a starter is removed from an engine, it is important to:Discover how the pitman arm connects the steering gear to the center linkWhich part in the front suspension is located between the steering gear and the center link?Distilled water is the right choice when refilling battery cells.What is the correct product to use when refilling battery cells?Documenting a customer's steering shimmy concern on the repair order sets the stage for accurate diagnosis and better service.What should a technician do after verifying a customer's complaint of steering wheel shimmy during hard braking?DOT 2 isn’t a brake fluid type—here’s what you need to know about brake fluids.Which of the following is not a type of brake fluid?DOT 5 brake fluid has the highest boiling point, making it ideal for high-heat braking.Which brake fluid type has the highest boiling point?During a 5,000-mile interval inspection, the air filter is checked to keep the engine running smoothly and fuel-efficient.What is checked during a routine 5,000-mile-interval inspection?Dye tracing and the red-fluid clue show how transmission leaks are found in cars.Technician A says that a leaking transmission line may be found by using a dye. Technician B says that a transmission leak would likely appear as a red fluid. Who is right?Electrical fires are Class C: what it means and how to respond safely.An electrical fire is what class of fire?Engine coolant leaks are a common sign that the water pump is failingWhich is a common symptom of a failing water pump?Engine overheating isn’t a sign of a failing alternator—here are the real symptoms to watch forWhich of the following is not a sign of a failing alternator?EVAP: What evaporative emissions are and why technicians focus on them during vehicle diagnosticsWhat system is referred to when a technician mentions "EVAP"?Extremely dirty air filters lead to poor engine performance.What is the result of extremely dirty air filters?Fender covers keep your car's paint safe while you work under the hood.To prevent damage to the vehicle's paint, what safety precaution should a technician take before working on an engine?Fender Covers Protect Engine Bay Paint During Auto RepairsWhat is used to protect painted surfaces in the engine compartment from scratches caused by a technician's belt?Fill a lead-acid battery with distilled water for safe, effective maintenanceA lead-acid battery with removable caps should be filled only with which of the following?Find the Manufacturer's ATF Specs in the Vehicle Owner's Manual for the Right Fluid and Service StepsWhere would a technician find the manufacturer's specification for changing automatic transmission fluid?Find the oil change reset steps in the owner's manual for vehicles with electronic warning systems.Where should the technician find the oil change reset procedure for a vehicle with an electronic oil change warning system?Find the Right Clutch Master Cylinder Fluid in the Service Manual for Your Vehicle.Where should a technician seek information on the correct fluid for a clutch master cylinder?Fluid leakage is a common sign of a failing transmission seal.What is a common symptom indicating a failing transmission seal?Flush eyes for 15 minutes after chemical exposure to protect vision.How long should eyes be flushed after a chemical has been splashed into them?Flush the eye immediately when a foreign object enters it to protect your visionWhat is the first step when a foreign object gets in one's eye?Following OEM gear lube specifications is essential for differential maintenance.Which of the following actions is advisable when dealing with a differential during maintenance?Front axle lubrication for rear-wheel-drive cars: wheel bearing grease is the right choiceWhich is the correct lubricant for the front axle on a rear-wheel-drive car?Front-wheel-drive cars rely on transaxles to power the front wheels.Front-wheel-drive vehicles have:Fuel pressure is the key metric checked during engine diagnostics.Which component is often monitored during a vehicle's engine diagnostics?Garages keep the old catalytic converter for 15 days after replacement to meet regulatory requirements.When a garage replaces a failed catalytic converter, how long must they retain the old converter?Gloves are the essential protection when handling sharp tools in auto repairWhat personal protective equipment is advisable when handling sharp tools?Goggles are the best eye protection when handling chemicals.Which type of eye protection should be worn while working with chemicals?Gold flakes in manual transmission fluid usually indicate worn synchronizers that make shifting roughIf fluid in a manual transmission has gold metal flakes, what is the likely cause?HEI Systems and Electrocution Risk: Why High-Voltage Ignition Demands Careful Safety Measures.What can an HEI system cause?Here's how the driveshaft links the transmission to the rear differentialWhich part in the drivetrain connects the transmission to the rear differential?HID Headlight Safety: Understand the Electrocution Risk and Handle Bulbs SafelyWhen handling HID headlight bulbs, which is a safety concern?High voltage safety matters when servicing a hybrid engine.What is a safety concern when servicing the internal combustion engine of a hybrid vehicle?How OSHA color codes help you locate the eye wash station in a shop.Using the OSHA system of safety colors, what color strip would indicate the location of the shop eye wash station?How the blower motor keeps high-voltage batteries cool in hybrids.What prevents high-voltage batteries in a hybrid vehicle from overheating?How the camshaft opens engine valves using the lifterWhich engine part does the camshaft move to open cylinder valves?How the crankshaft transfers torque to the transmission flywheel and why it mattersWhich engine part transfers torque to the transmission flywheel?How the HVAC System Cools the Passenger Area Using a Confined GasWhich system is used to cool the passenger area of a vehicle using a confined gas?How the torque converter multiplies engine torque to power automatic transmissionsWhat is the primary function of the torque converter in an automatic transmission?How to check transmission fluid on dipstick-free transaxles using the fill plugWhich would be removed on a vehicle transmission/transaxle without a dipstick to check the fluid level?How to measure the thickness of a solid metal rod with an outside micrometerWhat tool would be used to measure the thickness of a solid metal rod?How to use a fire extinguisher with the PASS method: Pull, Aim, Squeeze, SweepWhen using a fire extinguisher, what do the letters PASS stand for?Hybrids power the A/C compressor with high voltage to deliver efficient cooling.On a hybrid vehicle, which type of voltage powers the air conditioner compressor?Hydraulic fluid powers most power steering systems, not motor oil.Which type of fluid is most commonly used in power steering systems?If you find a broken tool in the shop, notify the instructor immediately.What should a student do when a broken tool is found in the shop?If you smell gas in a workshop, evacuate the area and notify authoritiesWhat should you do if you smell gas in the workshop?If you spot a green puddle under the front of your car, it's probably antifreeze leaking.A green liquid is found under the front of a vehicle. Which fluid is most likely leaking?In a drum brake, the wheel cylinder holds brake fluid and converts hydraulic pressure into braking force.Which part of the drum brake assembly contains brake fluid?In a Fire, Look for the Map by the Door to Find Your Escape Routes.In case of a fire, where would a student find out where to go?Inside the cylinder head, the valve stem seal keeps engine oil out of the combustion chamber.Which part belongs inside a cylinder head?Installing taller tires makes your speedometer read slower, and here’s why.Installing taller tires on a vehicle would cause the vehicle's speedometer to:Keep long hair tied back and jewelry secured in the shop to stay safeWhat should be done with long hair and jewelry in the shop/lab?Know when to replace your car's air filter by following the owner's manual.When should the air filter in a vehicle be replaced?Leaking heater core? The proper fix is to remove and replace the heater coreWhat is the necessary procedure when the heater core is leaking coolant?Learn how the blend door directs airflow from the footwell to the vents in your car's HVAC system.What is the name of the heating part that changes the airflow from the foot area to the vent area?Learn how to check the fluid level in a manual transmission by removing the fill plug.What is the correct method to check the fluid level in a manual transmission?Leave the square seal on the old oil filter to prevent leaksWhat should remain on the old filter when changing the oil?Liquid cooling keeps high-voltage systems in hybrids cool and efficientIn a hybrid vehicle, which of the following is a common cooling method for high-voltage systems?Lowering a vehicle onto lift stops is the key to automotive lift safety.Who is correct about automotive lift safety: Technician A, who says to keep lift arms close together, or Technician B, who says to lower the vehicle onto lift stops?Make sure the manual transmission fluid reaches the fill hole level for proper lubricationWhen refilling a manual transmission, what should the technician ensure regarding fluid levels?Make the last jump-start connection away from the battery for safetyWhen jump-starting a vehicle, where is the safest location to make the last connection?Manufacturers issue Technical Service Bulletins to guide auto repairsWho issues technical service bulletins?Mastering the three C’s of a work order—Concern, Cause, and Correction.What are the three C's associated with a work order?Material Safety Data Sheets explain their purpose and keep auto shop teams safe around chemicals.What is the purpose of a Material Safety Data Sheet (MSDS)?Milky transmission fluid means water has entered the transmission.While servicing a manual transmission, the technician notices the fluid is milky looking. What is most likely the cause?Moisture in manual transmissions matters for performance and longevityWhat substance should be checked for moisture when diagnosing a problem in a manual transmission?Mopping spills in an auto shop keeps people safe and the workspace efficientWho is correct regarding safety practices in the shop: Technician A, who says mopping up spills is good, or Technician B, who supports leaving workstations messy?NATEF recognizes technical training programs in auto repair.Which type of automotive program is likely recognized by NATEF?Nausea is a common warning sign of carbon monoxide poisoning.Which of the following is a common symptom of carbon monoxide poisoning?Neither A nor B is correct: brake cleaner on throttle bodies is risky and DOT 5 should not be mixed with DOT 3Technician A says it is acceptable to use brake cleaner to clean throttle bodies. Technician B says it is acceptable to mix DOT 5 brake fluid with DOT 3 brake fluid. Who is right?Nitrile gloves are essential when you’re cleaning parts with a parts washer.Which activity requires the use of nitrile gloves?No two vehicles share a VIN, and that unique identifier helps track a car’s history.How many vehicles have the same VIN?Oil air tools daily to keep them in good working condition.What should be done to air tools daily to keep them in good working condition?Oil filter wrench: the right tool to remove oil filters safely and efficiently.Which tool should be used to remove an oil filter?Oil viscosity matters: B is correct and A isn't.Technician A says all vehicles use the same oil viscosity. Technician B says using the wrong viscosity oil can damage an engine. Who is correct?Orange cables in hybrid cars mark the high-voltage wiring that powers the electric systemThe orange cables on hybrid cars indicate what?Orange wiring marks high-voltage systems in hybrid carsIn a hybrid vehicle, which color is typically used for the high-voltage wire?Over-torquing lug nuts can damage wheel studs and compromise wheel security.Over torquing lug nuts can cause:Oxygen is the key element in the fire triangle.Which is an element of the fire triangle?Personal protective equipment (PPE) keeps auto technicians safe with proper shoes, eye protection, ear protection, and masks.Proper shoes, safety glasses, hearing protection, and a mask are known as:Power steering fluid matters for smooth steering and long-lasting components.What type of fluid is typically used in a vehicle's power steering system?PPE in auto mechanics is designed to prevent workplace injuries and keep you safe.What is the primary purpose of personal protective equipment (PPE)?Pressurize a cooling system to the radiator cap rating to protect hoses and prevent overheatingWhen pressurizing a cooling system, how much pressure should be applied?Providing auxiliary 12-volt power before disconnecting a vehicle battery helps preserve radio presets, seat memories, and PCM data.Before disconnecting a vehicle's 12-volt battery for service, providing auxiliary 12-volt power to the vehicle will accomplish all of these except:Red fluid reveals automatic transmission leaks: what to check and why it mattersWhich fluid color would indicate an automatic transmission/transaxle leak?Refrigerant powers cooling in a car's air conditioner through the AC cycle.Which substance cools the air in an automobile air conditioner?Regular brake fluid level checks keep braking performance reliableWhat type of maintenance is essential for ensuring consistent brake performance?Replace the hub seal when installing a new wheel bearing to ensure proper sealing and lasting performance.What should be replaced to ensure proper seal and function when installing a new wheel bearing?Replace the U-joint when it's dry and loose to keep the driveshaft safeWhat is the proper repair if a driveshaft universal joint (U-joint) is dry and loose?Replacing the valve stems during tire installation keeps air pressure stable and tires safer.What is a good practice to do when installing new tires?Replacing torn windshield wiper blades restores clear, safe visibility.When windshield wiper blades are torn, which would be the correct fix?Resetting the maintenance reminder indicator is the final step after an oil changeWhich should be the last step in an engine oil change?Reusing the original gasket is often recommended when reinstalling an automatic transmission pan.When reinstalling an automatic transmission pan, which statement is accurate regarding the use of gaskets?Rings aren’t safe to wear in a shop because they can catch on machinery and cause serious injuries.Which item(s) would be unsafe to wear in a shop?Running an engine without a proper air filter can damage piston rings and reduce engine performance.If a vehicle has been run without the proper air filter, which part would most likely be damaged?Safety Data Sheets are for everyone: understanding access to chemical safety information.Who is allowed to read safety data sheets?Safety glasses and closed-toe shoes are the two must-wear items in every automotive shop.Which two safety items should always be worn in an automotive shop?Safety glasses in the workshop are mainly about shielding your eyes from debris.What is the primary objective of wearing safety glasses in a workshop?Set the A/C V-drive belt tension with a ruler to measure belt deflection accurately.When adjusting an A/C "V" drive belt, how can proper tension be determined?Shock absorbers keep your ride smooth and safe by damping road bumps.What is the function of shock absorbers in a vehicle?Shut off the power supply first—the safest move when you encounter an electrical problem in a vehicleWhat should you do if you encounter an electrical problem while working on a vehicle?Slow charging a completely discharged 12-volt battery: why 12 hours matters.What is the best method for fully charging a completely discharged 12-volt battery?Some manual transmissions may require motor oil: understanding fluid options for manual gearboxesRegarding the fluids used in manual transmissions, what can be stated?Store cleaning chemicals in a fire-retardant cabinet to keep your auto shop safe.Where should cleaning chemicals be stored in the auto shop?Store micrometers in a wooden or plastic box to protect precision and extend their lifeWhere should micrometers be stored while not being used?Storing flammable materials properly keeps your auto shop safe.What is the best way to ensure a work area is safe from fire hazards?Synthetic engine oil provides superior lubrication and protection for engines.Which type of engine oil is known for its superior lubricating properties?Technicians pinpoint suspension noises using chassis ears.Which is the most likely tool for a technician to use to find a noise traveling through the suspension system?Test tire pressure at the valve stem for accurate readings and safer drivingWhere on a tire should a technician test its pressure?The alternator powers the car's electrical system while the engine runs.What supplies electrical power to the vehicle when it is running?The brake light switch is the key to turning on your brake lights when you press the pedal.What component is primarily responsible for activating the brake lights when the pedal is pressed?The clutch is the key link between engine and transmission in manual cars.What component do manual transmissions/transaxles primarily use?The clutch is the key link between the engine and a manual transmission.What component transfers power from the engine to a manual transmission?The condenser sits directly in front of the radiator in a vehicle's air conditioning system.Which air conditioner component is located directly in front of the radiator on a vehicle?The cylinder head is bolted to the engine block, forming the seal that powers the engineWhich part is the cylinder head bolted to?The engine block is the car's backbone that provides structure and support.What is the primary role of the engine block in an automotive engine?The engine thermostat sits at the engine end of the upper radiator hose to regulate coolant flow.Where would an engine thermostat most likely be found?The fuel tank is a key part of the EVAP system, and here's why it mattersWhich part below is a component in the EVAP system?The MacPherson strut combines a shock absorber and coil spring into one compact unit.What type of suspension incorporates the shock absorber and coil spring in one assembly?The output shaft seal is the most likely source of transmission fluid leaks.Which component is most likely leaking if a technician notices fluid around the rear of the transmission?The owner's manual is where you record your vehicle’s service history.Which manual has an area to write service history in it?The primary job of a car battery is to start the engine, with the alternator taking over once it’s running.What is the primary purpose of a vehicle’s battery?The radiator is the quiet hero behind a car’s heating and cooling system.Which part is crucial for the vehicle's heating and cooling system?The red brake warning light sits on the dash to alert you to braking system issuesWhere is the red brake warning light typically found in a vehicle?The thermostat controls coolant flow in your car's cooling systemWhich part in the cooling system controls the flow of coolant?The thermostat opens the coolant flow when the engine overheats, keeping the engine cool.How does the thermostat respond when the engine temperature is too high?The TPMS sensor is essential for maintaining proper tire pressureWhat component is essential for maintaining proper tire pressure?The valve body is the key to how automatic transmissions shift gearsWhich component is primarily responsible for changing the gears in an automatic transmission?The water pump circulates coolant to keep your engine from overheating.What is the function of a water pump in an engine?Three pedals define a manual car: clutch, brake, and accelerator, and how they work.How many total pedals does a vehicle with a manual transmission have for driver controls?Top off a low lead-acid car battery with distilled water for reliable performanceWhile servicing a battery, the technician notices it is low on fluid. What should be added to the battery?Torquing lug nuts with the star pattern: the right way to seat wheelsWhen torquing lug nuts on a vehicle, which pattern should one use?Torquing wheel lug nuts to OEM specs helps prevent brake rotor warping and keeps your wheels secure.What is the function of torquing wheel lug nuts or bolts to OEM specifications?Transaxle: the name for front-wheel-drive manual transmissions and why it mattersWhich is the name of a front-wheel-drive manual transmission?Transfer case fluid isn't automatically the same as auto or manual transmission fluids.Which statement is true regarding transfer case fluid?Transmission fluid keeps automatic gear shifts smooth and reliableWhich fluid should be checked to ensure smooth gear operation in an automatic transmission?Two CV joints sit at each end of a front-wheel-drive CV axle.How many CV joints are on a front-wheel-drive CV axle?Under-torqued lug nuts can cause the wheel to fall off, and here’s how to prevent it.What is the most likely result of under-torquing lug nuts?Understand what the oil pressure gauge actually measures and why it matters for engine healthWhat does the oil pressure gauge measure?Understanding ABS pulsation during hard braking and who really uses itTechnician A says an ABS will pulsate the brakes during hard stops. Technician B says ABS brakes are found only on vehicles that have been imported. Who is right?Understanding ABS: what the Anti-lock Braking System does and why it matters for safe drivingIn terms of automotive safety, what does the acronym ABS stand for?Understanding ASE: What Automotive Service Excellence Means for Technicians and DriversWhat does ASE stand for in the context of automotive certification?Understanding DOT 5 brake fluid: silicone-based fluid with a higher boiling point and moisture resistanceWhich type of brake fluid is considered synthetic?Understanding engine oil grades: why 10w30 is the go-to for most enginesWhich type of fluid most likely goes into a vehicle's engine?Understanding how the chassis provides grounding in a vehicle's electrical systemWhich component helps to ensure good grounding in a vehicle's electrical system?Understanding radiators with two heat exchangers for engine coolant and transmission fluid.Some radiators have two heat exchangers, one for the engine and one for the:Understanding the battery hold-down: why it keeps your car's battery secure and reliableWhat is the primary purpose of the battery hold-down?Understanding the dial indicator: how it measures distance with precision in auto mechanicsWhat is the primary use of a dial indicator?Understanding the driveshaft: how power travels from the transmission to the rear axle in rear-wheel-drive trucksOn a rear-wheel-drive truck, which component transfers power from the transmission to the rear axle?Understanding the EVAP system components: charcoal canister, purge valve, and vent solenoid.Which components below are part of the EVAP system?Understanding the federal 8-year/80,000-mile warranty for catalytic convertersWhich is the federally mandated warranty period for catalytic converters?Understanding the four connections needed to safely jump-start a car with jumper cablesHow many connections are required when jump-starting a vehicle using jumper cables?Understanding the primary purpose of a fuel filter in a vehicleWhat is the primary purpose of a fuel filter in a vehicle?Understanding the Series Circuit: why a single path from plus to minus matters in auto electronicsWhich type of electrical circuit consists of only one positive and one negative connection?Understanding which part converts fuel into power in a car: the engineWhat component is responsible for converting fuel into power in a car?Understanding who accredits automotive programs and why it matters for students.Which organization is tasked with accrediting automotive programs?Understanding why a Battery Load Test Matters for Your Car's Electrical HealthWhat component is typically tested by performing a battery load test?Understanding why pink is identified as the color for new automatic transmission fluid.What color is optimal for newly added automatic transmission fluid?Understanding why the dimmer switch is essential for dashboard light brightness.Which part is essential to ensure proper functioning of the dashboard lights?Understanding why the red brake warning light stays on and what it means for braking safetyA vehicle's red brake warning light stays on whenever the ignition is on and the engine is running. Any of the following could be the cause except:Understanding yellow lines on an automotive shop floor helps keep people safe and moves everyone with confidenceWhat do the yellow lines on an automotive shop floor indicate?Unusual cabin odors signal a faulty car AC and what to do about itWhich of the following can be a symptom of a faulty air conditioning system?Use a chisel with a hammer to cut a rounded-off nut on a vehicleWhich tool would be used along with a hammer to cut a rounded-off nut on a vehicle?Use OEM-specific brake fluid when refilling the brake master cylinder to protect safety and performanceWhen refilling a brake master cylinder, what type of fluid should always be used?Using a Technical Service Bulletin to research common issues across the same year, make, and model.Which document is best for researching vehicles of the same year, make, and model with similar issues?Using a Test Light to Check Voltage at Headlights: A Simple, Practical GuideWhich electrical tool would a technician use to test for the presence of voltage at the headlights?Valve springs keep engine valves closed, ensuring compression and proper timing.Which item is designed to keep engine valves closed?Ventilation in auto shops matters: running a vehicle indoors can be deadly.What could be the result of running a vehicle in the shop without proper ventilation?Verify instrument lights when the key is turned on and the engine is offWhen is the correct time to verify that all the instrument lights function properly?Verify the correct transmission fluid and check for leaks before adding to protect your automatic transmission.What should be done when a technician finds fluid levels low in an automatic transmission?Water dripping on the passenger’s feet? The evaporator drain is the likely culpritWhat is the most likely cause of water dripping on a passenger's feet in a vehicle?Wear safety goggles for every automotive task to protect your eyes.During what circumstance should safety goggles be worn?What a catalytic converter does to cut harmful exhaust emissions.What is the role of a catalytic converter?What a clutch does in a manual car and why it matters for gear shiftsWhat is one of the main purposes of using a clutch in a manual transmission?What ANSI stands for and why it matters in automotive standardsWhat does the term ANSI stand for?What closes the valve in a cylinder head and why the spring mattersWhat closes the valve in a cylinder head?What color is the primary brake warning light on the dashboard, and why it matters for safetyWhat is the color of the primary brake warning light on the dashboard of vehicles?What do anti-rattle clips do in brake systems?What is the purpose of anti-rattle clips in brake systems?What document outlines first aid steps for a chemical spill? Understanding the Safety Data Sheet (SDS) in auto shops.What is the name of the document that outlines first aid action needed for a chemical spill?What happens when you disconnect a car battery without a memory saver and lose radio presetsWhat will happen if one fails to install a memory saver before disconnecting the battery?What HID stands for and why it matters for trucksA customer bought a set of HID headlights for a truck. What does HID stand for?What PPE stands for and why it matters in auto repair safetyWhat does the term PPE stand for?What the alternator does: it charges the battery and powers the car’s electrical systemWhat is the primary function of a vehicle’s alternator?What the EGR system primarily controls in an engine and why it mattersWhat does the "EGR" system primarily control in an engine?What the SRS warning light on your dashboard really means for your airbag safetyWhat does the SRS warning light represent on a vehicle's instrument cluster?What VIN stands for: Vehicle Identification Number and why it mattersWhat does "VIN" stand for?What yellow floor markings on an auto shop floor indicate and why they matter.What do yellow-painted areas on a shop floor indicate?When a bolt is too tight to loosen, the safest move is switching to a larger drive size for better leverageWhen a bolt or nut is too tight to loosen with the socket currently being used, which is the safest solution?When a car fuse blows, your first clue is a non-working electrical device like the radio or power windows.What is a common symptom of a blown fuse in a vehicle?When a car returns with a dead battery, check the vehicle service history to see past repairs.If a vehicle returns to the shop three times with a dead battery, where would one find past repair information of the vehicle?When a coolant recovery tank has a hole, replacing it is the right fix.If the coolant recovery tank has a hole in it, what is the proper fix?When a CV joint boot has a small split, replace the boot to protect the joint.What should be done if a CV joint boot is found to have a small split?When a DEF warning appears in a diesel, the vehicle can become disabledIf a driver ignores the dash warning message to refill a diesel vehicle with diesel exhaust fluid (DEF), what will be the end result?When a manual transmission is hard to shift, the clutch is often the culprit.In a manual transmission vehicle that is hard to shift, who is correct regarding potential issues?When a slave cylinder starts failing, the most common sign is trouble shifting gears.What is typically a common symptom of a failing slave cylinder?When a tailpipe rusts through, replace the entire assembly for safety and performance.If a tailpipe has a rusted hole in it, what is the proper procedure to repair it?When a tool breaks in the shop, tag it and report it.When a tool breaks, what should be done?When lug nuts aren't torqued correctly, rotors are the brake component most likely to warp.If lug nuts are improperly torqued when wheels are installed, which brake components are most likely to become warped?When should you replace the timing belt? A practical look at the 60,000–100,000 mile intervalWhen should a timing belt generally be replaced?When the check engine light signals a vacuum leak, start with a quick visual inspection.If the check engine light is on for a vacuum leak, which type of inspection would a technician perform first?When the exhaust manifold rusts, don't ignore it - here's how to protect your exhaust systemIf the exhaust manifold on a vehicle is rusty, what should be done?When the hydraulic clutch pedal has no pressure, the slave cylinder leak is the most likely culprit.If a hydraulic clutch pedal has no pressure, what may be leaking?When the instrument panel bulb won’t light, the bulb is usually the culprit.What is the most likely component to fail if a light does not illuminate during an instrument panel bulb check?When the transmission bell housing leaks, the front pump seal is usually the culprit.If a vehicle is leaking fluid from the transmission bell housing, which is the most likely cause?When transmission fluid leaks around the pan, replace the gasket to stop the leak.If fluid is leaking from around the automatic transmission pan, what should be replaced?Where to find the air suspension disable switch in your carWhere would one most likely find the air suspension system disable switch on a vehicle?Where to Find the Cabin Air Filter and Why It Impacts Your Car’s Air QualityWhere would a cabin air filter most likely be found?Where to Find the Fire Evacuation Route: A Simple Classroom GuideWhere is a fire evacuation route located?Where to Find the Master Cylinder: It sits in front of the brake pedal under the hoodWhere would one most likely find the master cylinder on a vehicle?Where to find the right horn fuse size for your vehicleWhere can a vehicle owner find information on the size fuse needed for the horn?Where to find the VIN on a vehicle: the driver's door frame and why it matters.Where on a vehicle should a VIN be found?Which ASE certification category isn't a real specialty, and what that means for service and maintenance.Which of the following is NOT an ASE certification?Which factor is least likely to affect headlight aim during a setup, and why it mattersDuring a headlight alignment procedure, which factor is least likely to impact the alignment?Which fluid goes in an automatic transmission? Understanding ATF and why it keeps gears shifting smoothlyWhich type of fluid goes in an automatic transmission?Which organization certifies automotive training programs and why it matters to studentsWhich organization certifies automotive training programs?Which pedal is the clutch pedal in a manual transmission, and why it's on the leftIn a vehicle with a manual transmission, which pedal is designated as the clutch pedal?Whining when you turn the steering wheel usually points to low power steering fluidIf a vehicle is making a whining noise when the steering wheel is turned, what is the most likely cause?Why 1,000-volt insulated gloves are the safest choice for hybrid power steering workBefore working on a hybrid vehicle's electrical power steering system, which personal protective equipment should a technician wear?Why 75W gear oil is the right choice for rear differentialsWhat fluid would most likely go in a rear differential?Why a 6-point socket is the go-to choice for hex nuts and bolts.Which type of socket will best hold a nut and/or bolt?Why a 50:50 coolant-to-water mix is standard in automotive cooling systemsWhat is the ratio of coolant to water in a typical automotive cooling system?Why a bad switch is the least likely cause when the left front park light failsIf the left front park light is not functioning, which of the following is least likely to be the cause?Why a breaker bar is the best tool for loosening rusted boltsWhich tool is best suited for loosening a rusted bolt?Why a face shield is essential when working with hazardous chemicals in auto repairWhat safety equipment is essential when working with hazardous chemicals?Why a fire evacuation route in a workshop is all about keeping everyone safe during emergencies.What is the primary purpose of a fire evacuation route in a workshop?Why a Multimeter Is the Right Tool for Measuring Vehicle VoltageWhat tool is typically best used for measuring voltage in a vehicle's electrical system?Why a Parts and Labor Guide Isn't a Reliable Source for Power Steering Fluid SpecificationsWhich of the following is NOT a likely source for determining the correct power steering fluid to be used in a vehicle?Why a rattling sound under your car usually points to a loose exhaust heat shieldWhat is the most likely cause of a rattling sound coming from the underside of a vehicle?Why a rear brake light can fail: both a blown bulb and a loose socket can keep it from illuminatingDuring an exterior vehicle inspection, a rear stop light is found to be inoperative. Technician A says a blown bulb could be the cause. Technician B says that poor connection at the bulb socket could be the cause. Who is right?Why a running car in an unventilated shop is the most dangerous carbon monoxide risk.Carbon monoxide poses a danger if a vehicle is:Why a special wire brush and baking soda work together to clean side-terminal battery terminals.Technician A says a specially designed wire brush is available to clean the terminals of a side-terminal battery. Technician B says that baking soda and water can be used to neutralize corrosion on battery terminals. Which is right?Why a specialty auto shop focuses on a single service area and what it teaches aspiring technicians.Which type of shop typically specializes in a specific area of automotive service?Why a squeaking brake means your brake pads may need replacement.What indicates that brake pads may need replacement?Why a torque wrench matters: applying the right force to fasteners in cars and machinesWhat is the purpose of a torque wrench?Why a tubing wrench is the right tool for removing brake lines and how it protects fittingsWhich tool would most likely be used to remove a brake line?Why a vehicle's differential lets the wheels rotate at different speeds.What is the purpose of a vehicle's differential?Why aluminum is the top material for new model cylinder headsWhat material are new model cylinder heads commonly made from?Why an eyewash station matters in auto shops and how it protects your eyesWhat is the purpose of an eyewash station?Why anti-rattle clips matter for brake pad stability and how to spot a missing partWhen diagnosing a vehicle with vibrating brake pads, which component is often missing?Why ATF isn’t interchangeable and color isn’t a reliable sign of the right fluid.Technician A says that all automatic transmission fluids (ATF) are interchangeable. Technician B says that new ATF should be pink in color. Who is right?Why changing engine oil when the engine is warm helps it drain more completely.When changing the engine oil, what should the temperature of the engine be?Why disconnecting the battery is essential when servicing HID lighting systemsWhen working on an HID lighting system, which component should be disconnected?Why does the AC serpentine belt jump off the pulley when the AC is turned on? Start by checking pulley and bracket positioning.What is the most likely cause if the A/C serpentine drive belt keeps jumping off its pulley when the A/C is turned on?Why following the manufacturer's transmission fluid change interval matters for your vehicleHow often should automatic transmission fluid be changed in a vehicle?Why gloves rated for 1,000 volts are essential when working on hybrid vehicles.When working on a hybrid vehicle, how many volts should the protective gloves be rated to handle?Why impact sockets are black and what that color tells you about their strengthWhat color are impact sockets?Why jack stands keep lifted vehicles from falling and how to use them safelyWhat should be placed under lifted vehicles to prevent them from falling?Why long necklaces and long hair aren’t safe in auto shops—and how to stay safeTechnician A says wearing a long necklace in the shop is a good safety practice. Technician B says long hair is acceptable while working around moving engine parts. Who is right?Why maintenance reminders are hard to reset and how that keeps your car on trackWhy is it usually difficult to reset maintenance indicators on a vehicle?Why nickel-metal hydride batteries are the standard for many hybrid cars.What type of battery is typically used in hybrid vehicles?Why Park Is the Right Gear for Checking Automatic Transmission Fluid LevelWhat gear selector position is typically used when checking the fluid level in an automatic transmission with a dipstick?Why radiator caps are pressurized and how it protects your engine.Why are radiator caps pressurized?Why replacing the transmission pan gasket is the wiser fix for a mild leakRegarding a mild fluid leak at an automatic transmission pan gasket, what is the best approach?Why short city trips wear out the clutch faster than long highway drivesIn which situation might excessive wear of the clutch occur?Why snap ring pliers are the right tool for removing snap ringsWhich tool is used to remove snap rings?Why Task Lighting Is Essential for Precise Auto WorkWhich component is essential for providing adequate lighting in a work area?Why technicians check OEM guidance before reusing transmission gasketsHow should technicians handle original gaskets during automatic transmission maintenance?Why the airbag wiring loom in the steering column is yellow and what that means for service safety.What color is the wiring loom going through the steering column for the supplemental restraint system?Why the car battery matters for the ignition system and engine startWhich component is crucial for the operation of a vehicle's ignition system?Why the catalytic converter is the key to cutting car emissionsWhich component works to reduce harmful emissions in a vehicle?Why the check engine light comes on and the role of the oxygen sensorWhile driving down the highway, Mary notices a check engine light on the dash. Which most likely caused the light to come on?Why the Diesel Exhaust Fluid Cap Is Blue and What It Means for Diesel MaintenanceDiesel exhaust fluid (DEF) is to be added to a new model diesel vehicle. The cap on the DEF reservoir/bottle is normally:Why the fuse is the safety guard in a car's electrical systemWhich component of the electrical system protects against a short circuit?Why the high-voltage disconnect in hybrids is orange and how it keeps people safeWhat color is the high-voltage disconnect in a hybrid vehicle?Why the open end of a wrench can round a frozen nut and how to loosen it safelyWhy would a technician not use the open end of a wrench to untighten a frozen nut or bolt on a vehicle?Why the pinch weld is the safest lifting point for most cars when you're jacking up a vehicleWhich part of a vehicle is considered an acceptable lifting point?Why the previous owner's problem isn’t listed on a work order and what information belongs on itWhat information is typically excluded from a work order?Why the Right Rear Brake Light Goes Out: A Bad Bulb Is Usually the CulpritIf a customer reports that the right rear brake light is out, what is the most likely cause?Why the transaxle is the common transmission setup in front-wheel-drive cars.What transmission configuration is most commonly found in front-wheel-drive vehicles?Why the water pump is the key to preventing engine overheatingWhich part below keeps the engine from overheating?Why the water pump isn’t the sole regulator of coolant flow and why the oil filter isn’t the regulator for oil flowTechnician A says a water pump controls the flow of coolant through an engine. Technician B says an oil filter controls the flow of oil through an engine. Who is right?Why tire tread is essential for safe vehicle handling and how to check it regularlyWhat should be inspected regularly to ensure safe and proper vehicle handling?Why wearing a ring while working on a vehicle poses a serious electrical burn risk and what to do instead.What is the risk of wearing a ring on one's hand while working on a vehicle?Why wearing loose clothing in an auto shop is a safety risk—and how to stay safeWhy should one avoid wearing loose clothing when working in an auto shop?Why yellow floor lines define a work area in auto shopsWhat color are the painted lines on the floor that define a work area?Why you should drain an oil filter for 12 hours before disposalWhat is the minimum recommended time to drain an oil filter before disposal?Why you should never reuse old gear lube when refilling a differential.What is NOT a recommended practice when replacing gear lube in a differential?You remove the fill plug to check a differential’s fluid level.What should be removed to check the fluid level in a differential?You'll find the cabin air filter in the engine compartment, not under the dashboard.Where might a cabin air filter be located aside from under the dashboard?

Subscribe

Get the latest from Examzify

You can unsubscribe at any time. Read our privacy policy